How to Install the Embedded Disinfection Cabinet?

Method/Step

1. Pay attention to the size of the cabinet when installing the built-in disinfection cabinet. The installation space should be larger than the size of the disinfection cabinet. For details, please refer to the manual.
2. The disinfection cabinet can be set at the bottom of the cabinet foundation or the upper part of the vertical cabinet as required.
3. In the reserved position of the cabinet, set a proper square hole, and insert the body of the disinfection cabinet into the square hole smoothly.
4. Pull open the cabinet door, fix the body on the door with six wood screws, flush.
5. The distance between the power socket and the disinfection cabinet should be controlled within 2m. Next Discount Code NHS

Related Experience

• How does an air energy water heater work
• How to install the water retaining strip
• How to install air energy water heater
• How to distinguish the prices of different types of aluminum alloy doors and windows
• How to hang gypsum board

The method of drawing flush nuts in solidworks

1. This article introduces the method of using solidworks to draw flush nuts. The tools used are mainly the extruded boss tool, and the polygon drawing tool in the sketch is used at the same time. I hope it will be helpful to everyone.

Draw Flush Nut

1. First, draw a sketch on the top view datum plane, use the polygon tool to draw a hexagonal sketch, the size of which is shown in the figure below, do not exit the sketch after drawing.
2. Then, in the sketch editing state, click the feature, and select the extrude boss tool in the feature toolbar to stretch the sketch.
3. Next, continue sketching on the top plane, using the circle tool, draw a circle sketch on the center point.
4. Then use the stretched boss tool in the feature tool to stretch the circle sketch. The thickness of the stretch is as shown in the figure below, so that the main model of the flush nut is obtained.
5. Finally, using the Hole Wizard tool in the feature toolbar, a threaded hole is inserted in the center, thus completing the modeling of the flush nut.

How To Draw A Flush Hairstyle Head

This article introduces: how to draw a flush hairstyle head

• pen and paper
• colour pencil

Detail

1. Draw the face shape of the task, which is a square face.
2. Then draw the hair and ear shapes.
3. Then paint the texture of the hair.
4. Then draw the eyes, nose, and mouth of the character.
5. Take out the colored pens.
6. Give the hair orange.
7. Put some pink on the cheeks, rosy and healthier.
8. It’s done.

Precautions

1. I wish you success and every step of the way.
2. Please give me a thumbs up in the lower left corner.

CD-ROM installation Method

The CD-ROM drive of the desktop computer is broken, and many of them will manually replace and install a new CD-ROM drive. Today I will share the installation method

Explanation

1. The first thing is to remove the left and right panels of the computer case, and the optical drive is also ready
2. In the reserved position of the optical drive of the chassis, remove a panel
3. Carefully insert the new CD-ROM into the
4. After inserting all the way, make the outer face flush with the surrounding panel
5. Fix the screws on both sides of the optical drive to maximize the firmness of the optical drive
6. Find the power cable and data cable of the optical drive and connect them correctly.

High flush, length aligned, width equal, learned in elementary school

1. Height, level, length and width are equal, which is learned in the second semester of the third year of junior high school.
2. Students have learned three views in the compulsory education stage. The three views in high school are the process of revealing the essence of numbers and shapes.
3. The focus is on drawing the three views of simple combinations. The difficulty is to identify the geometric models represented by the three views. This micro-lesson aims to Designed for students to grasp key points and break through difficulties.
4. The main contents are: Review the concept of three views; be able to draw simple spatial figures and three views of simple composites; identify the geometric model represented by the three views; the mutual transformation between the three views and geometry.

Course Design Ideas

1. By reviewing the concept of three views, guide students to draw three views of a triangular prism (junior high school did not give a specific definition of a triangular prism).
2. Understand that the length of a line segment that is not parallel to the projection plane is different from its orthographic projection, and master the “long alignment” of the three views, height level, width equal” specific meaning.
3. Design the three-view of the combination of a cuboid with one corner cut off and a right-angled trapezoid rotated around the upper base, understand the relationship between the placement angle of the object and the three-view, and understand the idea that the invisible line must be drawn with a dotted line.
4. The design of the last senior high school entrance examination question allows students to experience the process of imagining the spatial figure from the plane figure, then draw the plane figure of the side view from the space figure, and experience the thoughts of naturalization and transformation Wayfair Promo Codes NHS at NHS Discount Code.

Installation skills of hardware and sanitary ware

1. Installation of the handle: The installation of the handle should be ergonomic and easy to use. When installing, all handles of the same wardrobe must be neat and consistent. The length of all screws should match the thickness of the cabinet door and drawer surface. When drilling holes with an electric drill, the size of the hole should be consistent with the diameter of the screw.
2. Door hinge installation: Generally, two hinges with a length of 100mm are installed on the door. If it is a solid door or a concave-convex door, three hinges must be used, or two hinges with a length of 125mm must be installed.
3. Installation of locks: After the door lock is installed, the distance between the handle and the ground should be between 900-1000mm.
4. When installing, install the lock body and deadbolt first, make the deadbolt plate flush with the edge of the door, close the door, fix the position of the striker plate, install the striker plate, and ensure that the striker plate is flush with the edge of the door pocket.